-
While loading bulk oil, you notice oil on the water near the bargeWhich of the following actions should you carry out FIRST?（）
A . Search the vessel for leaks
B . Notify terminal superintendent
C . Stop loading
D . Notify the Coast Guard
-
You have orders to drop off a barge loaded with propylene oxide at a fleet.In doing so，you must ensure that（）.
A . All wing voids and rakes are pumped dry before tying off the barge
B . The barge is moored next to the bank where it will be protected from a possible collision
C . The barge is under the care of a watchman
D . A rake end is facing upstream to minimize the effect of current on the mooring line
-
In securing deck loads for an ocean tow，drill pipe should be（）.
A . galvanized to protect against corrosion
B . held in place with heavy materials such as spare pendant wire
C . limited to no more than five courses high
D . provided with bulwarks at both ends of their bay
-
Increasing the load on an engine equipped with a constant speed mechanical governor, will cause the engine speed to initially （）.
A . increase
B . decrease
C . fluctuate
D . remain constant
-
（）are to be used for dunnage if you load rice.
A . Wooden planks
B . Rush mats
C . Steel bars
D . Wooden planks and rush mat
-
If you had started loading earlier，you（）loading now.
A . would finish
B . will have finished
C . would have finished
D . will be finished
-
How should you signal the crane operator to raise the boom and lower the load?（）.
A . Extend arm with the palm down and and hold this position rigidly
B . Place both fists in front of the body with the thumbs pointing outward each other
C . Clasp hands in front of you body
D . Extend arm with the thumb pointing up, and flex the finger s in and out for as long as the load movement is desired
-
How should you signal the crane operator to lower the boom and raise the load?（）.
A . Extend arm and point finger in the direction to move the boom
B . Extend arm with the thumb pointing downward and flex fingers in and out
C . With f rearm vertical and forefinger pointing up,move hand in small horizond circles
D . With arm extended downwards and forefinger pointing down,move hand in small horizontal circle
-
An “on-load” release system on a survival craft means the cable can be released（）.
A . only when the load is taken off the cable
B . only when there is a load on the cable
C . only when activated by the controls at the lowering station
D . at any time
-
You are configuring a JMS server with a need for load balancing the messages. To achieve the load balance you should （）.
A . use regular queues and topics
B . use distributed queues and topics
C . not use subdeployments
D . disable server affinity
E . use message paging
-
During counterflooding to correct a severe list or trim aggravated by an off-center load，a ship suddenly takes a list or trim to the opposite side. You should（）.
A . continue counterflooding in the same direction
B . continue counterflooding，but in the opposite direction
C . immediately stop counterflooding
D . deballast from the low side
-
If a leak occurred while loading diethylenetriamine，the chemical data guide indicates you would smell an odor similar to（）.
A . ammonia
B . rotten eggs
C . gasoline
D . None of the above
-
An emergency generator, driven by an internal combustion engine, shall be tested under load for a minimum of 2 hours at least once every （）
A . week
B . 2 weeks
C . month
D . 3 month
-
Cargo contaminated due to failure to provide clean holds prior to loading is an example of（）.
A . lack of due diligence
B . restraint of princes
C . inherent vice
D . latent defect
-
What does the proof test load of an anchor chain demonstrate?（）
A . Breaking strength of the chain
B . Strength of the chain to a specified limit
C . Adequate holding power for new bottom conditions
D . Safe working load of the chai
-
If you are loading fruit in reefer spaces and you notice that the fruit is beginning to mold, you should（）.
A . carry the cargo at a cooler temperature than originally planned
B . write up exception on the cargo
C . refuse to carry the cargo
D . discharge CO
into the compartment after loading
-
A spring-loaded centrifugal flyweight governor responds to reduced engine load with an immediate increase in （）
A . pilot valve oil pressure
B . speeder spring force
C . compensation needle valve clearance
D . centrifugal force on the flyweight
-
The instantaneous reduction in voltage of an AC generator, resulting from an increase in load, and prior to the automatic voltage regulator correcting the situation, is called voltage （）.
A . droop
B . drop
C . dip
D . regulatio
-
You have a large amount of historical data in an operating system file. Some analysts in your organization need to query this data. The file is too large to load into your current database. Which is the most effective method to accomplish the task？（）
A . Upgrade the hardware/memory to accommodate the data.
B . Load the data into your database by using the PARALLEL clause.
C . Give analysts DBA privilege， so that they can query DBA_EXTERNAL_TABLES.
D . Use an external table so you can have the metadata available in your database， but leave the data in the operating system files.
-
An increase in load on a diesel engine results in （） of speed of the crankshaft.
A . a reduction
B . an increase
C . an outing
D . a downward
-
Your tanker is loaded down to her marks，and you find that she has too much trim by the stern. To adjust the trim，you may（）.
A . add ballast forward
B . load more cargo forward
C . shift bunkers forward
D . All of the above
-
The load rating of an AC generator is determined by the（）
A . internal heat it can withstand
B . load it can carry continuously
C . load it is capable of supplying
D . overload it can carry for a specified time only
-
You create a Web Form that allows users to create a new account. You add a CreateUserWizard control by using the following code segment.You need to ensure that the wizard automatically sends an e-mail message to users when they finish creating their accounts. You add a valid element to the Web.config file.Which code segment should you add to the Page_Load event？（）
A.Wizard1.RequireEmail = True
B.Wizard1.Email = "user@address.com"
C.Wizard1.MailDefinition.From = "registration@mysite.com"
D.SmtpMail.SmtpServer = "mail.contoso.com"
