-
A system administrator thinks that a filesystem may be full and that is what caused the machine to crash. Which command will show the administrator if they are correct?()
A . du
B . df
C . fsck
D . ncheck
-
Which command shows your active Telnet connections?()
A . show session
B . show cdp neighbors
C . show users
D . show queue
-
Which line from the output of the show ip interface command indicates a layer 1 problem?()
A . Serial0/1 is up, line protocol is down
B . Serial0/1 is down, line protocol is down
C . Serial0/1 is up, line protocol is up
D . Serial0/1 is administratively down, line protocol is dow
-
Which statement best describes what is depicted in the show command output?()
A . IGMP snooping is not active for VLAN 120 because the IGMP feature has not been enabled on the switch with the feature igmp command.
B . The IGMP snooping querier for VLAN 120 is not in a running state because the Loopback interface configured with 1.1.1.1/32 is currently in a down state.
C . IGMP snooping has been disabled on the VLAN 120 SVI.
D . IGMP snooping has been disabled for VLAN 120 in VLAN configuration mode.
E . IGMP snooping is not active for VLAN 120 because VLAN 120 does not exist in the VLAN database.
-
Which command will display messages directed to the system console?()
A . alog -t console -o
B . cat /var/adm/ras/conslog
C . cat /var/log/all/console.log
D . grep CONSOLE /var/adm/message
-
A System p administrator is investigating a possible security breech and wants to review information about failed login attempts to the system. Which of the following commands will show this()
A . fwtmp < /etc/security/failedlogin
B . cat /etc/security/failedlogin
C . who
D . alog -f /etc/security/failedlogin -o
-
The man page for command shows the following syntax: The man page for command shows the following syntax: command [ -a -b ] Which of the following statements is true regarding this entry?()
A . Either the -a or flag -b may be used, but not both.
B . If the flag -a is used then the flag -b also must be used.
C . One of the -a or -b flags must be used, but not both at the same time.
D . Both the flags may be used together, but neither are mandatory.
-
Which command shows if an access list is assigned to an interface?()
A . show ip interface [interface] access-lists
B . show ip access-lists interface [interface]
C . show ip interface [interface]
D . show ip access-lists [interface]
-
While applying a service update on a system using SMIT, the system administrates SMIT Command Status screen shows "Command: failed". Which of the following procedures should be performed to investigate the failure?()
A . Exit the SMIT session and re-apply the update.
B . Select the SMIT option to Clean UP After an Interrupted Installation.
C . Examine the installation summary report to determine the cause of the failure.
D . Examine the console log to view the error messages generated by the failure.
-
After executing the "show host" command, which of the information below would you see?()
A . The IP addresses of workstations allowed gain access to the router via an access list
B . Permanent name-to-address mappings created using the ip host command.
C . Temporary and permanent DNS entries.
D . The names of the routers created using the hostname command.
E . The length of time of users logged into the router, as well as the duratio
-
Which of the following commands will show how many physical partitions are available on active hdisk1?()
A . lspv hdisk1
B . lsvg -p hdisk1
C . lsattr -p hdisk1
D . lsdev -E -l hdisk1
-
Which command will show the network configuration settings associated with an Ethernet adapter?()
A . lscfg
B . lsdev
C . netstat
D . ifconfig
-
Which of the following pieces of information will the command show interface provide?(Choose allthat apply.)()
A . Layer 1 status
B . Output queue drops
C . Interface CPU utilization
D . Cable type connected to interface
E . Layer 2 status
F . Input queue dro
-
A System p administrator has just installed a new technology level, but "oslevel -r" does not show the expected technology level. Which of the following commands would determine which filesets are downlevel()
A . lppchk
B . instfix
C . oslevel
D . install
-
Which command shows all the paging spaces available on a system?()
A . lsps -a
B . showps -a
C . psdisplay -l
D . swaplist -ALL
-
If a system administrator wants to show only a disk report for disk2, at two second intervals, what is the correct command to run?()
A . iostat disk1 1
B . iostat -d disk1 2
C . iostat disk2 1
D . iostat -d disk2 2
-
Which command shows all the paging spaces available on a system?()
A . lsps -a
B . showps -a
C . psdisplay -l
D . swaplist -ALL
-
Which command shows if an access list is assigned to an interface?()
A . show ip interface [interface] access-lists
B . show ip access-lists interface [interface]
C . show ip interface [interface]
D . show ip access-lists [interface]
-
Which command will show the MAC addresses of stations connected to switch ports?()
A . show mac-address
B . show arp
C . show table
D . show switchport
-
Which show command will display only the Type 5 LSAs in the OSPF topology database?()
A . show ip ospf database external
B . show ip ospf database nssa - external
C . show ip route ospf
D . show ip ospf datab ase summary
E . show ip route
-
Which of the following commands should be used to show DNS information?()
A . trace
B . netstat
C . ifconfig
D . nslooku
-
Which command shows dump components and controls live dump attributes?()
A . dumpctrl
B . sysdumpdev
C . livedumpdev
D . livedumpctrl
-
Which command shows your active Telnet connections?()
A . show session
B . show cdp neighbors
C . show users
D . show queue
-
Which IOS command shows the detailed error report?()
A . errpt -A
B . errpt -a
C . errlog -a
D . errlog -l